He bought InterLink XP.
HDD It is 30GB.
It is enough.

Although it was --, since he wanted to have come to decompose somehow, it decomposed. (It is ねん with what)
The probability in which 換装 is possible feels that it is high also for 3210 in the same procedure.

The procedure of decomposition was allowed to carry out the writing of interchange RINKUSURE of る to reference in my two.

moreover -- since I do not てま responsibility, either, even if it works reading the following procedures and ぶっ壊 a machine -- please .

Before decomposing.
Since the screw of various length uses it, being intermingled, understand InterLink XP later. Please be sure to classify.
Although the standard of the length of a screw is once written also to the following procedures Disagreeable [ be and ], if discernment is possible for every procedure number It is the level to say.
I hear (the screw which should be attached if it collects by the touch "the screw removed by procedure 5" and "procedure 5" will be seen afterwards is known.). If all are made ちゃ混ぜ, although what is written here is read, which does not understand it for some.

1. First, all the things that can be removed ordinarily are removed.
   • SD dummy card
   • PC card
   • Battery
   • Battery terminal cover
   • Other cables
   
   
2. A hinge cover is removed.
   It will separate, if it pulls and is made to raise from back.
   
   
   
3. A main part is turned over and it is a memory extension mouth. All screws other than the screw of 3 つ are removed.
   If the screw shown by the red arrow is removed, since a built-in battery will come to fall out, it extracts.
   Moreover, only the screw shown by this red arrow is somewhat shorter than others.
   
   
   
4. A keyboard is removed.
   If TSUME in three upper ends is pushed by the nail in a minus driver, it can be removed.
   TSUME is the following. It is in 3 parts (I will think that it understands, if it sees).
   
   • F12 Between the Pause keys
   • On F6 key
   • Half size / full-size key Between F1 keys
   Since TSUME is removed and a keyboard assembly is floated, please extract a connector (two), and remove a keyboard.
   
   
5. Screw which removes a keyboard and came to appear All 6 books are removed.
   • The screw on the right-hand side of an upper end is a silver screw with the somewhat small head.
   • Center The screw under JVC LOGO is the longest in this. (All aluminum board, main board, and PC card slots are fixed)
   • All other screws are the same.
   
   
   
6. All visible connectors are removed.
   • Liquid crystal going x2
   • Right-and-left speaker
   Since the connector of the right for liquid crystal is fairly hard, please do your best.
   It says and needs pushing a lug of right and left little by little by turns, and removing it. (It warns against damaging a substrate)
   It is safe if it pushes by the thing (smile) hard a tree, the stick of a plastic, etc. and soft. (2002/9 / 25 addition/.) nud The guardian deity of children since -- information
   
   
   
7. A palm rest + liquid crystal display is removed (I think that it is the first difficulty).
   Although it is very hard to remove this side side (mouse button side), please remove here first (making it float).
   Since it will separate if a palm rest is shifted at back and a main part bottom is shifted to the front, please make it reference.
   
   * 2002/9 / 25 additions : removed [ that it is said that it is / way / easy ] from TSUME on the backside. nud The guardian deity of children since -- information
   
   
   Then, it is if TSUME near [ where a Num Lock state etc. is displayed ] a place (it is visible if it sees from a built-in battery side) is stuffed into the back and removed. --
   
   The unit with which a palm rest and liquid crystal were united separates.
   Under the present circumstances, although it may not separate easily, the aluminum board of a chip set and the keyboard reverse side may adhere because of the heat conduction sheet which exists between them.
   In this case, if power is applied slowly, it can remove.
   
   
   
8. It is the complete view of a main board.
   The red arrow showed. The screw of 4 books is removed.
   
   • The screw with an immediately silver next door of a built-in battery terminal (it is thick and is short)
   • The screw with immediately silver width of an external battery terminal
   • A headphone jack is a back silver screw a few.
   • The silver screw which is fixing the daughtercard of a modem (since it passes to the chassis, it is long)
   
   
   
9. A main board is removed from a main part bottom.
   Although a headphone terminal and a microphone terminal are caught, since it does not separate unless it raises from the side here, please carry out skillful く outside.
   If the side there is raised, a main board will be removed by the touch which draws out the left-hand side of a main part.
   
   
   
10. The transparent seal near the external battery terminal of a main board is removed, and it is black. An HDD fixed screw is removed.
    
    
11. A main board is turned over. HDD is removed.
    Since the HDD fixed screw is already removed, the connector of HDD is in the state of only 差さっている.
    Please turn over, damaging and twisting a connector and pressing down like and HDD.
    
    
    
12. It is new. It exchanges for HDD and finishes setting up in a reverse procedure.

It is the touch to say!
I think that し outside TSUME of a palm rest and the length of a screw should take care.
I think that there is especially no place that the rest changed. Many